Katalog

Katalog Alat

Berikut adalah beberapa Katalog Peralatan PDKB-TM, dari mulai Merek Yotsugi, Tanizawa, Nagaki, Izumi, Hastings, dan Skylotec

HOT STICK TESTER

Tester

HOT STICK TESTER

• Test hot sticks wet or dry. The tester has a selector switch for wet or dry tests and a dual range scale which gives the operator leakage current values in micro amps.
• Utilizing a 2,500 volt output, the meter is calibrated to indicate the leakage values that would be present if 75KVAC were applied to a 12” section of the fiberglass tool for the wet test and 100KVAC per foot for the dry test.
• Portable and lightweight for easy use. Two models available 120 volt or 220 volt systems. The tester is designed to protect the operator while in use.
• The tester comes complete with a padded carrying case and directions for proper use. A testing bar is also provided to ensure the tester is working properly.
• Application and training video included with purchase.

Detail Produk

INSULATED JUMPER HOLDER

Grounding and Jumper Equipment

INSULATED JUMPER HOLDERS

• Designed to provide the lineman safety when installing and removing energized jumpers
• Allows linemen greater control with all jumpering requirements
• Can be installed with all standard shotgun sticks or rubber gloves

Detail Produk

BY PASS JUMPER WITH MECANICAL PROTECTIVE TUBE

Conductor And Personal Support

INSULATED / PROTECTED JUMPERS 15-69KV*

• 15KV rated cable is encapsulated in a 1 3/4” O.D. fiberglass tube. The fiberglass tube gives added insulation and mechanical protection for jumpering switch gear, reclosers and cutting in double deadends.
• Cable can be removed for inspection and replacement
• Fiberglass hanger brackets allow clamps to be secured for installation and removal of jumper
• Can be installed on wire sizes from 8 solid .120 diameter up to and including 1,033 MCM 1.25 diameter
• *Ratings - 69KV rating applies to area on fiberglass tube between red bands which are 12” from ends of the tube. 15KV ratings apply outside the red bands. Ratings apply for accidental brush contact only.

Detail Produk

BY PASS JUMPER BERJARAK 35 KV

Grounding and Jumper Equipment

35KV FACTORY ASSEMBLED HOT STICK APPLIED JUMPERS

• Consists of (2) ground clamps 21575, jumper cable, (2) ferrules 13101 and (1) hanger stud 13190-1

Detail Produk

BY PASS JUMPER BERJARAK 25 KV

Grounding and Jumper Equipment

25KV FACTORY ASSEMBLED HOT STICK APPLIED JUMPERS

• Consists of (2) ground clamps 11190, jumper cable, (2) ferrules 11658 and (1) hanger stud 13210

Detail Produk

BY PASS JUMPER SL 25 KV / 35 KV

Grounding and Jumper Equipment

  1. 25KV FACTORY ASSEMBLED JUMPERS WITH MEDIUM RANGE HEADS - CLEAR
  2. 25KV FACTORY ASSEMBLED JUMPERS WITH LARGE RANGE HEADS - YELLOW
  3. 25KV FACTORY ASSEMBLED JUMPERS WITH LARGE RANGE HEADS - CLEAR
  4. 35KV FACTORY ASSEMBLED JUMPERS WITH LARGE RANGE HEADS - YELLOW
  5. 35KV FACTORY ASSEMBLED JUMPERS WITH LARGE RANGE HEADS - CLEAR
Detail Produk

BY PASS JUMPER SL 15 KV

Grounding and Jumper Equipment

  1. 15KV FACTORY ASSEMBLED JUMPERS WITH MEDIUM RANGE HEADS - YELLOW
  2. 15KV FACTORY ASSEMBLED JUMPERS WITH MEDIUM RANGE HEADS - CLEAR
  3. 15KV FACTORY ASSEMBLED JUMPERS WITH LARGE RANGE HEADS - YELLOW
  4. 15KV FACTORY ASSEMBLED JUMPERS WITH LARGE RANGE HEADS - CLEAR
Detail Produk

SAFETY PLATFORM

Conductor And Personal Support

SAFETY PLATFORM

• Light weight polyethelene
• Provides extra protection when working from ground, pulling conductors or when working near energized equipment
• Supports up to 300 lbs
• Heavy non-skid surface on top prevent slips
• Extra large legs with non-skid base to prevent tipping or skidding
• Sturdy handles built in on all 4 sides - easy to carry and transport
• Filled with unicellular polyurethane foam to provide a strong lightweight surface
• Dimensions 24” wide x 30” long x 12” high
• NOTE: For maximum protection platform must be kept free of dirt, dust or contamination.

Detail Produk

INSULATED PLATFORMS

Conductor And Personal Support

INSULATED PLATFORMS

• Work platforms are designed for maximum safety and ease of installation
• Permanent non-slip surface in the work area
• Metal castings and components on platforms are made from heat-treated aluminum alloys
• Platforms have square channel foot/toe stops for location awareness
• Platform width is 10 3/4”
• Twin adjustable struts for stability
• Complete with braces and chain tightener
• The rail assembly hinges and stores on top of the platform by removing the keeper pin
• The horizontal rail assembly is a positioning device that will allow the worker to maintain proper work positioning and balance
• Not to be used as an anchor point - see anchor point tool page 316
• Platform can be positioned in 30 degree increments up to 180 degrees under load by loosening wheel tightener. No need to get off the board to reposition

Detail Produk